Redsbaby Bounce (2016 Model) - Instruction Manual

Redsbaby Bounce (2016 Model)

Instruction Manual

Contents

General instructions 3

Warranty information 4

Warnings and safety precautions 6

Features and components 8

Assembly instructions 9

Frame 9

Brake component 9

Rear wheels 10

Front swivel wheels 10

Bassinet and bumper 10

Removing the bassinet and bumper 11

Seat and bumper 11

Basket 12

Using your Redsbaby Bounce 13

Folding and unfolding 13

Engaging and releasing the brake 14

Locking the front swivel wheels 14

Adjusting the handle 14

Using the 5-point safety harness 15

Reversing and reclining the seat 16

Reversing the bassinet 16

Using the tether strap 16

Lifting and carrying your Redsbaby Bounce safely 16

Accessories – Assembly and Use 17

Rain cover 17

Bounce Canopy 17

Bassinet apron 17

Noslip™ Contoured Seat Liner 18

Maxi-Cosi Capsule Adaptors - Travel System 19

Product Care 21

General Instructions

This document contains important information and must be kept for

future reference.

Please read thoroughly before commencing assembly and use of your

Redsbaby Bounce. Incorrect assembly and use can be dangerous and

result in serious injury or even death.

There may be slight variations in the design of your product to that shown

in the images of this instruction manual.

Warranty information

12 Month Warranty

The Redsbaby Bounce and its accessories come with a 12 Month

Warranty to cover against faults in materials and workmanship when

your products are used under normal conditions, according to our user

manuals and technical specications.

Our goods come with guarantees that cannot be excluded under

the Australian Consumer Law. You are entitled to a replacement or

refund for a major failure and compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the goods

repaired or replaced if the goods fail to be of acceptable quality and

the failure does not amount to a major failure.

The 12 Month Warranty period starts from the date your product(s)

are dispatched from our warehouse. This includes products that are

purchased via pre-sale (for example items that are out of stock or newly

launching products). Please remember that for a claim to be valid, it must

be made within the claims period.

There are a few circumstances under which the warranty is not valid

including:

- defects resulting from improper care or use;

- normal wear and tear, including scratches to the stroller frame;

- products that are purchased second hand or from an unauthorised

distributor;

- faulty or incorrect assembly;

- using a part or accessory that is not compatible with the product and/or

not manufactured by Redsbaby;

- tyre punctures; and

- damage to handlebar grips or fabrics as a result of normal handling and

daily use.

For a full list of what is covered and what is excluded from the warranty,

please read our Terms and Conditions at www.redsbaby.com.au. Please

ensure you follow the assembly instructions, which can be found in this

instruction manual.

How To Make A Warranty Claim

Send an email to info@redsbaby.com.au to notify us of your warranty

claim. To validate your warranty claim we will require you to include in

your email:

- a description of the warranty defect including photographs;

- your contact details;

- attached invoice with order number; and

- product batch number (the batch number is printed on a sticker that

is located on the crossbar above the shopping basket on the stroller

frame).

We will respond to your warranty claim within 7 business days and

depending on the nature of the warranty claim, arrange collection of

the product from your nominated address. Collection will take place on

a business day (i.e. not a public holiday or weekend within your state

or territory) between 7am and 5.30pm. Please take care to repack the

product in secure and stable packaging to avoid any damage occurring

in the returns transit. We do not take responsibility for any damage that

occurs in transit to and from our pram repairer.

Once our pram repairer has received the product they will inspect

and conrm the reported defect. We will then contact you with further

information surrounding the repair such as the estimated turn around

time.

If you have any questions, you can contact us at info@redsbaby.com.au.

Warnings and safety precautions

Please read the following warnings and safety precautions thoroughly

before using your Redsbaby Bounce. Incorrect assembly and use can

result in serious injury or death.

Always follow safety instructions for assembly, folding and use.

Always ensure that your Redsbaby Bounce is correctly assembled and

locks are engaged before use.

After unpacking, immediately discard any plastic wrapping and

packaging materials, as these can lead to a choking hazard.

Always use the safety features that come with your Redsbaby Bounce,

such as the tether strap, brakes and harness.

GENERAL WARNINGS:

• To avoid injury or death: Always apply the brakes whenever the

Redsbaby Bounce is stationary.

• Do not leave children unattended.

• Secure the child in the harness at all times.

• Do not carry extra children or bags on the Redsbaby Bounce.

• Make sure children are clear of any moving parts if you adjust the

Redsbaby Bounce, otherwise they may be injured.

• Follow the manufacturer’s instructions.

• Put on all the brakes whenever you park the Redsbaby Bounce.

• Use the harness at all times.

• When not in use disconnect shoulder straps from the waist strap and/or

buckle.

• The harness can form loops which may cause a strangulation hazard.

Never leave a harness connected when not tted to a child in the

Redsbaby Bounce.

• Use the tether strap to stop the Redsbaby Bounce rolling away.

• Do not use the seat or bassinet with any other models of stroller.

• Do not use bassinet once the child can sit up unaided.

• Only use the bassinet in the at position. Do not recline.

• Do not use any accessories that are not designed for or compatible

with the Redsbaby Bounce.

• Take care when used on stairs or escalators.

• Do not use or leave the Redsbaby Bounce near open re or exposed

ame.

• Brakes must always be applied when the Redsbaby Bounce is not

moving.

GENERAL SAFETY PRECAUTIONS:

• When the vehicle is being folded and unfolded, there is potential

for ngers or parts of the body to be injured and due care should be

exercised.

• Overloading, incorrect folding or the use of non-approved accessories

may cause injury or damage your Redsbaby Bounce.

• Ensure you follow the regular maintenance and care instructions

included in this manual. Pay special attention to maintenance and care of

the brakes.

• The Redsbaby Bounce must only be used for one (1) child.

• Do not hang bags on Redsbaby Bounce handles, as this can cause it to

become unstable.

• Do not lift or carry the Redsbaby Bounce when a child is in it.

• Do not lift or carry the Redsbaby Bounce when fully assembled. Only lift

and carry when folded.

• The Redsbaby Bounce is designed for use on at or gentle sloping

surfaces and may be unstable on higher sloping and uneven surfaces. The

vehicle may tip over when used incorrectly on steep inclines/declines.

• Do not leave the rain cover on without the ventilation window on the

front of the rain cover open.

• When using your Redsbaby Bounce on stairs or escalators, take care.

MAXIMUM WEIGHT LIMITS:

• Maximum weight for a child in the bassinet is 9kg (19.8 lbs).

• Maximum weight for a child in the seat is 17kg (37.5 lbs).

• Maximum weight for items in the pockets on the back of the seat is 1kg

(2.2 lbs).

• Maximum weight for items in the basket is 5kg (11 lbs).

Features and components

1. Handle

2. Fold locks

3. Bassinet apron

4. Frame fold

latches

5. Brake

6. Rear wheels

7. Canopy

8. Circular frame

9. Bassinet

10. Frame

11. Basket

12. Front swivel

wheels

13. 5-point safety

harness

14. Seat with seat

liner

Assembly instructions

Frame

To release the frame from the folded position:

1. Place frame on the ground and position yourself behind the handle bar.

2. Pull back on the two frame fold latches located on either side of the

frame simultaneously.

3. Holding the frame on either side of the disengaged frame fold latches,

gently lift the frame continuing until the frame locks into place. When the

frame has been fully opened, you will hear and feel a rm ‘click’.

Brake component

Align the brake component with the two rear ends of the pram. Click

the brake component into place. Ensure that the brake component is

assembled correctly by checking the two silver locking pins located on

the underside of the rear brake component are in place.

2 3

Sticker Label

55mm

Sticker Label

55mm

Sticker Label

55mm

Rear wheels

Fit the rear wheels on the axle housings located on either side of the rear

brake component. You will hear and feel a rm ‘click’ when the wheels

are locked in place.

IMPORTANT: Ensure you check that the wheels are clicked in correctly

by tugging them outwards. Failure to attach the wheels correctly will

result in them falling o the pram while in use.

To remove, simply press the button in the middle of the wheel to release.

Front swivel wheels

Fit the front swivel wheels by inserting them into the front wheel locks

located at the front of the frame. You will hear and feel a rm ‘click’ when

the wheels are locked in place.

Assembling the bassinet and bumper

1. Secure the Velcro tabs on the bassinet lining around the circular frame.

Ensure the end of the lining which has the warning label is secured

around the end of the circular frame which has the two plastic clasps that

the canopy clips into.

IMPORTANT: Ensure each velcro tab is secured as tighly as possible.

2. Place the bassinet board in the bottom of the bassinet liner. Secure

using the Velcro tabs located at the top and bottom ends of the bassinet

liner onto the bassinet board.

3. Place the bassinet mattress on top of the bassinet board.

4. Secure the bassinet apron using the Velcro tabs provided.

5. If desired, attach the bassinet bumper by aligning the ends of the

bumper with the two openings on the circular frame. Gently push down

into place until your hear and feel a ‘click’ on both sides. Check the

bumper bar is locked securely.

WARNING:

• Do not use bassinet once the child can sit up unaided.

• This bassinet is only approved for use with model Redsbaby Bounce.

• The maximum weight of a child that can be carried in this bassinet: 9kgs.

• Only use the bassinet in the at position. Do not recline.

11. If desired, attach the canopy by following the instructions on page 17.

12. To place on the frame, push down gently until you feel and hear a

‘click’.

Removing bassinet and bumper

1. Remove the bumper by simultaneously pushing the buttons on either

side of the bumper and lifting upwards.

2. Remove the bassinet apron by releasing the Velcro tabs.

3. Remove the bassinet mattress.

4. Remove the bassinet board by releasing the Velcro tabs at the top and

bottom ends of the bassinet board and gently lifting out.

5. Release the Velcro tabs on the lining from around the the circular

frame.

Assembling the seat and bumper

1. Take the fabric seat unit and stretch the head rest section over the top

of the circular frame.

2. Pull the rest of the seat unit fabric tightly towards the bottom of the

frame. Take the safety straps and hook over the side of the frame.

3. Turn the frame over and then clip both ends of the safety strap

together. Tighten if necessary.

4. Wrap the foot area around the bottom of the circular frame and secure

rmly onto the Velcro strips at the bottom of the seat fabric.

5. Attach the bumper by aligning the ends of the bumper with the two

openings on the circular frame. Gently push down into place until you

hear and feel a rm ‘click’ on both sides.

6. If desired, attach the canopy by following the instructions on page 17.

7. To place the seat on the frame, push down gently until you feel and

hear a rm ‘click’.

WARNING:

• Do not use this seat with any other models of stroller.

• This seat is only approved for use with model: Redsbaby Bounce.

• The maximum weight of a child that can be carried in this seat: 17kgs.

Basket

IMPORTANT: Maximum weight for items in the basket is 5kg.

Note: Your Redsbaby Bounce will come with the basket assembled.

To Remove:

1. Unscrew the basket from the pram frame at the front.

2. Release the buttons that secure the basket to the basket rods.

Using your Redsbaby Bounce

Folding and unfolding the Redsbaby

Bounce frame

To release the frame from the folded position:

1. Pull back on the two frame fold latches located on either side of the

frame simultaneously.

3. Holding the frame on either side of the disengaged frame fold latches,

gently lift the frame and place on the ground.

4. Continue to lift the handle until the frame fold locks engage.

IMPORTANT: When the frame fold locks have been engaged correctly

and the frame has been fully opened, you will hear and feel a rm ‘click’.

To fold the frame

1. Remove the bassinet or seat unit if attached to the frame.

2. Simultaneously pull back on the frame fold locks on the left and right

hand side of the frame.

Tip: You can rest the handle bar on your waist to provide some resistance

if required.

3. Gently fold the frame downwards until the frame fold latches

automatically engage.

Note: The frame fold latches will engage automatically.

Note: If the front swivel wheels become caught, gently toggle to lay

sideways.

4. Turn the handle bar inwards by pressing the buttons located on either

side simultaneously.

Tip: You can also fold the Redsbaby Bounce with the seat connected in

the fully upright and forward-facing position.

WARNING:

• Make sure children are clear of any moving parts when you adjust the

Redsbaby Bounce, otherwise they may be injured.

• Ensure the frame fold locks are engaged correctly before placing a child in

the Redsbaby Bounce.

Safe lifting and carrying of the Redsbaby Bounce frame when folded

IMPORTANT: Do not lift or carry the Redsbaby Bounce when a child is in it.

IMPORTANT: Do not lift or carry the Redsbaby Bounce when fully

assembled. Only lift and carry when folded.

1. Always lift and carry the frame using two hands.

2. Ensure the frame fold latches are engaged.

Engaging and releasing the brake

The brake is located between the rear wheels of the Redsbaby Bounce.

The brake bar is identied by two red components on either end.

1. To engage the brake, press down on the brake bar at the rear of the

Redsbaby Bounce with your foot until you feel the brake engage.

2. To release the brake, lift the brake bar up with your foot until the brake

lock disengages.

Locking the front swivel wheels

1. Press downwards on the tab buttons located at the front of the wheels

until you hear and feel a ‘click’.

2. Push the Redsbaby Bounce forwards until you hear a second click in

both front wheels.

3. To unlock, simply lift the tab buttons upwards. When released

successfully, you will hear and feel a ‘click’.

Adjusting the handle

Note: Your handle can be adjusted to ve height options.

Simultaneously press the buttons located on either side of the handle and

move the handle to the desired height.

Using the 5-point safety harness

WARNING:

• Use the harness at all times.

• When not in use disconnect shoulder straps from the waist strap and/

or buckle. The harness can form loops which may cause a strangulation

hazard. Never leave a harness connected when not tted to a child in the

Redsbaby Bounce.

IMPORTANT: For the safety of your

child the 5-point safety harness must

be properly tted and adjusted. Follow

the instructions and Figure 1 below.

1. Ensure the seat is assembled correctly

by following steps on page 13.

2. Ensure the seat bottom is sitting at

on the seat.

3. Slide the shoulder strap clip (A1)

onto the waist strap clip (B1) and clip

into the center buckle (C).

4. Slide the shoulder strap clip (A2)

onto the waist strap clip (B2) and clip

into the center buckle (C)

Note: When your child is smaller, you

can feed the shoulder straps through

the loops provided on the seat back so

that the shoulder straps sit just above

the shoulders of your child.

5. Adjust the shoulder strap (A1) and (A2) and waist straps (B1) and (B2) to the

desired t.

6. To unlock the 5-point safety harness, simply press the button in the middle

of the centre buckle (C) to release all straps at once.

Note: Padding has been provided for the shoulder straps (A1) and (A2) and crotch

strap (D) for the comfort of your child. The use of this padding is optional.

Figure 1

B1 B2

WARNING:

• Use the tether strap to stop the Redsbaby Bounce rolling away.

Reversing and reclining the seat

IMPORTANT: Do not reverse or recline the seat when a child is in it.

1. To recline, press and hold both round buttons on the side of the seat

and move into the desired position. When in place, you will hear and feel

a rm ‘click’.

2. To reverse, remove the seat unit by pressing the rectangular release

buttons on either side of the seat unit and lift upwards. When the release

locks are disengaged, you will hear and feel a rm ‘click’. The seat unit

can be tted either rear or forward facing.

Reversing the bassinet

IMPORTANT: Only use the bassinet in the at position. Do not recline.

To reverse, remove the bassinet by pressing the rectangular release

buttons on either side of the bassinet unit. When the release locks are

disengaged, you will hear and feel a rm ‘click’. The bassinet unit can be

tted either rear or forward facing.

Using the tether strap

Attach the tether strap to your wrist at all times when using the Redsbaby

Bounce.

Lifting and carrying the Redsbaby Bounce safely

IMPORTANT: Do not lift or carry the Redsbaby Bounce when a child is in

it.

IMPORTANT: Do not lift or carry the Redsbaby Bounce when fully

assembled. Only lift and carry when folded. For folding instructions, refer

to page 11.

Accessories

IMPORTANT: The following accessories are only compatible with

Redsbaby Bounce. Do not use with any other model of pram/stroller.

Rain Cover (Sold Separately)

IMPORTANT: Do not leave the rain cover on without the ventilation

window on the front of the rain cover open.

Note: The canopy must be attached to the Redsbaby Bounce before

securing the rain cover.

Starting at the back of the canopy, gently pull the rain cover over the

bassinet or seat. Ensure the canopy peak is ipped over in the forward

position to ensure correct tting of the rain cover.

Bounce Canopy

To assemble

1. Pull the canopy over the top of the circle frame and clip the canopy

onto both sides of the circle frame above the bumper bar.

2. If using the seat, secure the velcro tabs on the canopy to the velcro

tabs on the top of the seat.

Bassinet Apron

Fit the bassinet apron by securing the velcro straps on the bassinet apron

to the bassinet liner.

Tip: Folding back the bassinet apron to see your child.

You can unzip either side of the bassinet lining and fold the bassinet

apron backwards.This will enable you to see your child without having to

remove the whole bassinet apron.

WARNING:

• Do not use any accessories that are not designed for or compatible with

the Redsbaby Bounce.

Noslip™ Contoured Seat Liner

Remove the shoulder and crotch padding from the Bounce seat unit

harness. Lift the seat unit up and place the elastic strap underneath the

seat and ip back out.

Align your seat liner on the Bounce seat unit. Feed the ve point safety

harness through the respective crotch, waist and shoulder strap holes. If

desired, replace the shoulder and crotch padding.

Maxi-Cosi Capsule Adaptors - Travel System

Note: Accessory sold separately

Securing the adaptors to your

Redsbaby Bounce chassis

1. Ensure your chassis is assembled

correctly by following the instructions

in your Redsbaby Bounce Instruction

Manual.

2. Stand behind your Redsbaby Bounce

handle bar, and click the adaptor

marked with the ‘R’ symbol into the

right-hand side, with the ‘R’ symbol

facing outwards. You will hear and feel a

rm ‘click’ when the adaptor is in place.

3. Repeat with the adaptor with the ‘L’ symbol, clicking it into the left hand

side, with the ‘L’ symbol facing outwards. See Figure 2.

FIGURE 2

FIGURE 3

FIGURE 4

PRESS

Securing your Maxi Cosi capsule into

your Redsbaby Bounce adaptors:

1. Hold the Maxi Cosi capsule facing

you, and using both hands push the

capsule down onto the adaptors to click

into place.

IMPORTANT: To check that the capsule

has clicked in correctly, lift the handle of

the capsule upwards.

See Figure 3.

To remove your Maxi Cosi capsule

from your Redsbaby Bounce

adaptors:

1. Press the left and right release

buttons on the Maxi Cosi capsule. Lift

upwards.

See Figure 4.

To remove your Maxi Cosi adaptors from your Redsbaby Bounce

chassis:

1. Press the grey release buttons on each adaptor. When the release

locks are disengaged, you will hear and feel a rm ‘click’ and you can lift

them upwards to remove.

Product care

IMPORTANT: Ensure you follow the regular maintenance and care

instructions. Pay special attention to maintenance and care of the brakes.

General Maintenance

• Regularly inspect the locking devices, brakes, harness assembly, catches,

seat adjusters, joints and xings to ensure they are secure and in full

working order.

• Do not store your Redsbaby Bounce in your car boot for prolonged

periods of time, especially when it is hot and this can lead to warping

some of the plastics parts and reduce the life of your product.

• The brakes and wheels are subject to wear and should be replaced as and

when necessary. Brakes are available through contacting our customer care

team at info@redsbaby.com.au.

• Should any parts of the Redsbaby Bounce become stiff or difcult to

operate, ensure that dirt is not the cause. Use a light application of a silicone

spray lubricant, ensuring the lubricant penetrates between the components.

Use sparingly, as excessive application may encourage the accumulation

of dirt. Regular light lubrication of moving parts will extend the life of your

Redsbaby Bounce and make operating, opening and folding much easier.

• Do not leave the Redsbaby Bounce in sunlight for prolonged periods of

time, as the colour of some fabrics may fade.

• Store the Redsbaby Bounce in a dry, well-ventilated and safe place.

• Do not use your Redsbaby Bounce if any screws are loose or missing or if

any component is damages.

Cleaning

Plastic and metal parts

• Sponge clean with warm water and a mild detergent and then air dry.

• Do not use any abrasive or corrosive cleaning products on your Redsbaby

Bounce.

Fabrics

• May be cleaned by sponging lightly with warm water and a mild soap

(ensure your child is not allergic to the soap you use). Then air dry.

• For more instructions, follow the care labels on each fabric item.

IMPORTANT: Do not place any fabric or other component of your Redsbaby

Bounce in the dryer. Allow all parts to dry thoroughly before storing.

YOUR REDSBABY BOUNCE

‘Redsbaby’ is a registered Trademark of Redsbaby Pty Ltd.

ABN 31 167 364 178.